|
The iPod Suffle is a really cool piece of hardware. One of the
drawbacks, however, is that it has an internal battery that is
recharged via USB power when it is plugged into your computer. This is
all good and well except that it requires a good 4 hours to charge the
Shuffle from completely dead to completely full. If you're on the road
this can be rather impractical. Thus, there was a need for a
batterypack/charger device that can extend the usefulness of the
Shuffle. Apple sells such a device
but it is rather expensive for what it does. Granted it looks very
nice, but I knew I could make the same product for less. And who can
give up a chance to solder?
iPod Shuffle Charger
February 12, 2005
Alternatives
Hack-A-Day has a similar project.
The trick is that if you want the shuffle to function properly you have
to tie both data pins (green and white wires) to ground. Pick you
poison, this is the only trick you need to be aware of when making a
Shuffle-specific charger.
Ingredients
To make a Shuffle Charger you will need the following:
- 1 +5VDC Voltage Regulator (RadioShack #276-1770) - $1.59
- 1 9v Battery Snap Connector (RadioShack #270-325) - $1.99 for a 5 pack
- 1 Project enclosure (I used a RadioShack #270-1802) - $2.69
- 1 General purpose PC Board (*optional) (RadioShack #276-149) - $1.79
- 1 9v battery - $2.99 or less
- A
female type A usb connector. You can find this off of a USB extension
cable, or maybe some old junk hardware somewhere. - $0.00 - $6.99
Total for parts: About $12 - $15.
Tools
Additionally you will need the following tools:
- Soldering Iron
- Solder
- Possibly some very high gauge wire (26 - 28 gauge)
- Screwdriver
- Volt Meter
Disclaimer
Look, I hardly know what I'm doing. This worked for me, but it might
not work for you. If you solder together your own charger and something
goes wrong and you fry your Shuffle don't come crying to me. You take
full responsibility for messing up your own Shuffle if you try this. If
you are worried, buy apple's battery pack and don't take the chance.
You have been warned.
Assembly
Note: Read all directions before beginning!
First, lay all the parts out on the table, and make sure that you have everything accessible.
Cut your usb cable in half and peel back the insulation so that you have all the wires out.
Strip the ends of the wires on the usb cable. Take the green, white, and black wires and twist them together.
Heat up the soldering iron and get it ready. Remember to always use saftey glasses when soldering!
The first solder you're going to make is from the 9v battery clip to
the voltage regulator. Solder the RED (+) wire to the INPUT on the
voltage regulator. Check the back of the box to make sure, but this is
usually the left-most pole.
Next, solder the white, black, and green usb twisted wires, AND the
ground (-) from the 9v clip to the ground on the voltage regulator.
This is probably the middle pole on the voltage regulator.
Finally, solder the (+) RED wire on the USB cable to the OUTPUT of the voltage regulator. This is probably the rightmost pole.
Next, double check your solder connections to make sure they are correct and there is no solder bleed-over.
 Now
connect the + probe on your volt meter to pin 1 on the usb connector,
and the - (black) probe to the other pins. On each pin the volt meter
should read +5v. It is critical that you verify the output voltage for each pin. If you mess this up you could break your Shuffle!
If you are satisfied (and brave), connect the Shuffle to the usb
connector. It should blink green, then yellow and green, and finally
blink yellow steadily. If it does this, then your charger works.
Congratulations! If not, check your solder joints and get your volt
meter out again. And pray you didn't fry your shuffle!
Finally, mount the parts inside the project case. I cut a notch on one
end just wide enough for my usb connector, and filled the empty space
with foam I had lying around from something I had shipped to myself.
There's no perfect way to do this. Just do what you think works. Heck
you don't have to mount it at all if you don't want to!
Okay, now grab a beer and watch as your yellow light blinks on-off-on-off-on-off-on-off...
|
Consumer Electronics 
