Putting it all together

I will not get into the nitty gritty of building the machine, as it is very simple and a waste of both of our time. Put the motherboard into the case, connect the powersupply to the motherboard, install the harddrive and DVD drive into the case, and then connect them via a IDE cable to the motherboard. You will notice that if you used the ASRock P4Dual-915GL board, you only have one IDE channel. Set your Harddrive to master and your DVD drive to slave. One quick note, hopefully you purchased a DVD drive, and didn't skimp on a CD drive as we will need a DVD drive to boot our installation DVD. =)

After you have all the hardware installed into the case, do a test run by connecting the onboard video to a monitor and connect a USB KEYBOARD and mouse. You should see a normal bios boot, eventually ending in a boot failure. (because we didn't give it anything to boot from) You should now restart the computer and enter the BIOS (usually del or F2 buttons) and make sure that it is set to boot from CD first. Now put your patched Marklar-Tiger DVD into the dvd drive and restart.

It is worth mentioning at this point that we are going to discuss the method of installing OSx86 onto the entire harddrive. There are ways of dual-booting your system with your favorite other operating system, but we will not cover that. Check the Wiki for more info on doing that. For your first time I suggest you install it on a blank drive all by itself. It removes a lot of the problems you could face.

As your computer boots from the DVD, you will be presented with a boot menu. This menu will be pretty familiar to those of you who have used unix or linux in the past, but for those of you who have not seen this before:

Darwin Boot Menu

This menu from now on will be referred to as the "Darwin Boot Menu" and it gives us the option of specifying specific boot options. Press your "F8" key to see the different boot options available. At this time I would not suggest using any of the options (you can just press enter) but it is very nice to know these options incase anything goes wrong. (The -v is a great switch allowing you to see any major errors such as kernel panics, etc) After you press enter you should be presented with the following familiar screen:

During this time, you will notice that the wheel spins, and your DVD-ROM thrashes.. Don't pat yourself on the back yet though, we are not even close to being done. After all the pre-installation files are loaded, you will be presented with a nice installation GUI. However take your time here. For this installation, we don't want to do the windows "next, next, next, next, next" type install.

Before we begin, we need to partition the drive accordingly. If you purchased your drive from ebay, or had an old one laying around -- chances are that the drive already contains partitions, and if you bought it new, it will not have any yet. You will want to go into the Disk Utility by clicking on Utilities-Disk Utility on the top menu.

Once you are inside Disk Utility, make sure to delete ANY and ALL partitions on this drive. (This of course will destroy ALL data on this drive, so make sure you are ok with that). Once you have deleted all of the existing partitions (if there were any) you can now create a new partition that uses the entire drive. Highlight the hard drive you are going to install OSx86 on and click the Partition button. At this point a new dialogue window appears, asking your to decide on a partition scheme. Click the Volume Scheme drop down menu. It lists different schemes to choose from, so just select 1 Partition.
By default the partition size will occupy the entire contents of the drive so, that amount will be reflected in the partition size box. If you wish to make a smaller partition just for the OS, say maybe 10-20GB, enter the appropriate amount in the box and press Enter. The volume scheme display on the left will change to reflect the size you've chosen. Give the partition a cool name like OSx86, and choose "Mac OS Extended (journaled)" as the format type. Then go ahead and hit the "Partition" button to set your changes.

Disk Utility will ask "Are you sure" before writing your new changes to disk. I can't stress this strong enough. IF YOU CONTINUE, YOU WILL LOOSE EVERYTHING ON THIS DRIVE. If you are following this tutorial, that is ok because we are using a spare drive to install to.

Once the partition has been written, I suggest you do a verify on the partition you created. You can do this by clicking on "First Aid", select your new partition (OSx86) and clicking the "Verify Disk" button. People have reported problems using the Disk Utility, consider this insurance that your partition is correct. Once it is verified, and you are happy with your new partition, you will need to exit the Disk Utility and return to the main OSX installer.

.

Ok, we now have our hard drive all setup, and waiting on a nice OSx86 load to be put on it. You can breathe a little now, as most of the hard work is completed. You will return to the main OSX Install screen, now we can start with our "next, next, next, next" campaign. Once you hit the "Continue" button you will be presented with a license agreement. Blindly agree and move on. =) The next screen will ask you which drive you intend to install OSX on. Select the drive (partition) that we just created.

If you don't see a drive icon there (or any drives listed at all), then you have a problem and I suggest you start the installation process over. If you do see it, click on Continue. A quick note before we go any further. On the next screen you will see a little "Customize" button down. What kind of a hacker are you if you don't press it? In here you are given the option to change what we are going to install. Here is what I suggest you do: (You do not need to do any of this, it is fine as it was)

• Remove any printer drivers that you are not going to need. (no one needs 1.6GB of printer drivers)
• Remove the Xcode Tools. These are the developer tools for creating x86 code to run on OSx86 and for transcoding current PPC code and software to the x86 platform. If you're not a coder, hacker or programmer this stuff can be deselected to save a chunk of drive space. (Saving you 1.7GB of space)

Leave the rest as they are, and press Install. Are you ready for this thing to get installing? Well next OSX wants to check the media for any problems. SKIP THIS. You have done all kinds of error checking along the way (remember all that MD5 work you did?) to know that your DVD is probably ok.

Finally OSx86 Begins to install. Don't be fooled by the time estimates, it will take a lot longer than it says.

If everything goes as planned, after the install process is complete your OSx86 will give you a 30sec countdown and restart. Congrats your *ALMOST* done. As your computer restarts, remove the installation DVD. You will see that your computer now boots to the Darwin Boot Menu. Press Enter to continue into OSX. As OSX boots, you are presented with a Welcome screen. You can probably handle it from here, all you will be doing is creating User accounts, and configuring network items.

A trick that I learned from the README file of the Release1 Patch, when you get to the Registration screen, press Alt+Q to skip the Registration process. Saves a lot and trouble. After you are finished here, your machine will finish booting into OSX. Before you start doing ANYTHING, I suggest you restart the machine one more time.

Now that you have OSx86 installed, lets do some clean-up. Click Go on the menu bar at the top of the screen, click Utilities. On the window that appears, double click Disk Utility. Select your OSx86 partition on the left hand pane then click Repair Permissions. This relatively simple step can resolve a lot of hassles, especially related to kexts that have incorrect permissions.

Congrats, you now have a working OSX installation running on Intel Hardware. I would like to add that this installation is not "final" or "legit" meaning that you WILL find bugs, and probably will have problems down the road. I suggest you read the forums mentioned earlier for help with any problems that may arise.

Also, since this install is a hack, and not legit, you will miss out on patches and fixes. For example, I checked for updates, and it told me that there were none available (although there are several patches to OSX 10.4.1) Running a unpatched machine is an invitation for trouble, so consider this your warning.

However, the hackers that brought you this install disc are also working on patches, If you check the torrent sites, you can find a patch that will update "OSx86 Update - 10.4.1 to 10.4.3"

This tutorial used hardware that was very similar to the hardware used in the development machines, however there is a LOT of room for improvement. I chose hardware that was very cheap to keep the project as close as possible to the $200 limit. You can build your system according to your budget, just make sure that you check the HCL before buying any hardware. Upgrades you should consider would be more ram, better processor (make sure it supports SSE3), and of course a sweet G5 Case to install it in, but you will of course go way over the $200 budget that was set for this article.

**UPDATE**  The folks over at AllMac are willing to give I-Hacked readers a discount on G5 Cases.  If you use the coupon code "I-Hacked" you can get the entire G5 Case enclosure for $129.99.  (Normally $159.99)  This includes The Enclosure, Optical drive Brackets, Optical Drive plate, HDD Fan & Brackets, Air Baffle and the Front panel!

But that didn't stop me from putting this machine through its paces, with some SURPRISING results!

I downloaded Xbench (a OSX Benchmarking Utility) and put my new OSx86 up against my Mac Mini. I wanted to see how this $200 machine faired against my $500 mini. As you can see from the results, (compare to my Mac Mini results the "IH-" boxes are mine) the OSx86 machine put a pretty good hurting on the Mini. Although the Mini held its own in several categories (it did after all have twice as much ram), I say the conclusion is that I am glad Apple is moving to Intel Architecture.

Now, do you need to buy all new equipment to get OSx86 running?  Of course not.  May of you may already be running hardware that is compatible.  To check your Processor to ensure that it supports SSE3 (or SSE2) you can download and run the windows application CPU-Z.  The hardware that we chose for this article was done so on purpose, the Processor, Motherboard Chipset, Video Chipset, and network chipset matched fairly close to the development machines.  This guide does not cover installing OSx86 on systems that do not meet this criteria.  However you can find tons of information at the sites listed below.

I would like to thank everyone from the win2osx.net and osx86project.org forums for all the help and information. I would also like to especially thank Mashugly, Mage66, br0adband, and Bender for the work and documentation they have done. (Not to mention Deadmoo and countless others who have contributed to the project)